DE34 OUTDOOR/INDOOR MINI
DE34 OUTDOOR/INDOOR MINI
PART No 988868 or 988869
CAB
ACTIONS TICK
POWER CABLE (WITH PLINTH)
CABLE ENTRY SEALS X 4 LRG X 4 SMALL
CABINET CLEAN
FIXED WIRING CORRECT
CORRECT DOOR
BCFA X 1
TRUA X 1
PSUB X 1
AFEM X 1 & Cable set
EARTH STUD 991898A X 1
DOOR EARTH STRAP X 1
CCFU X 1 (INDOOR ONLY)
4 FIXING BOLTS
BLANKING PLATES
DOOR DAMPER X 2 TOP & FRONT DOOR
TRXA X 1
SIGNATURE............................................
DATE........................................................
Page 2 Live
DE34 OUTDOOR/INDOOR MINI
PART No 988868 or 988869
CAB
TEST Final Insp. TEST Final Insp.
All gold standard units fit subrack Check door aligned
Earth Bond Test Cam hook bar/hinges/latches are greased & operational
Flash Test Door silk screening undamaged
Electrical ATE Test Gas struts operating correctly
Top connector plate silk screening legible EMC seals free from paint & blowholes
Earth point labels fitted EMC seal bonded to the door
Rubber bungs fitted ESD labels & studs fitted
No top surface damage Grommet strips on subrack 5 off
Orientation & bend radius of baseband cables as drawing All screws are fitted & torque
BNC locking nuts on Abis board are tight No tools left in cabinet
Covers for Rf connectors fitted All warning labels fitted 12off
Connector block wiring secure Paintwork on exterior or cabinet to NEMS spec
Paintwork on lid near door handle No contaminants inside the cabinet (or loose fasteners)
No loose connections on the top plate Loose cables are wrapped and secure
All RF connections are tight Cabinet cleaned
Top surface power cable routing as Nokia drawing Fixing kit placed in packing
Document pocket variant label complies with job card Cabinet is correctly fitted to base of packing
Tie wrap bases on picture frame to drawing RF cables are not damaged (no copper exposed)
Check magnetic switch on door & sensor secure Check subrack is secure
Door/lid has earth screw & cable fitted Check subrack rails are not damaged/bent
Interior cabling is neat and not trapped Check backplane connectors are not bent
Check backplane is not scratched
Check jumper setting pins are not bent
Check cable indents
PART No 988868 or 988869
CAB
ACTIONS TICK
POWER CABLE (WITH PLINTH)
CABLE ENTRY SEALS X 4 LRG X 4 SMALL
CABINET CLEAN
FIXED WIRING CORRECT
CORRECT DOOR
BCFA X 1
TRUA X 1
PSUB X 1
AFEM X 1 & Cable set
EARTH STUD 991898A X 1
DOOR EARTH STRAP X 1
CCFU X 1 (INDOOR ONLY)
4 FIXING BOLTS
BLANKING PLATES
DOOR DAMPER X 2 TOP & FRONT DOOR
TRXA X 1
SIGNATURE............................................
DATE........................................................
Page 2 Live
DE34 OUTDOOR/INDOOR MINI
PART No 988868 or 988869
CAB
TEST Final Insp. TEST Final Insp.
All gold standard units fit subrack Check door aligned
Earth Bond Test Cam hook bar/hinges/latches are greased & operational
Flash Test Door silk screening undamaged
Electrical ATE Test Gas struts operating correctly
Top connector plate silk screening legible EMC seals free from paint & blowholes
Earth point labels fitted EMC seal bonded to the door
Rubber bungs fitted ESD labels & studs fitted
No top surface damage Grommet strips on subrack 5 off
Orientation & bend radius of baseband cables as drawing All screws are fitted & torque
BNC locking nuts on Abis board are tight No tools left in cabinet
Covers for Rf connectors fitted All warning labels fitted 12off
Connector block wiring secure Paintwork on exterior or cabinet to NEMS spec
Paintwork on lid near door handle No contaminants inside the cabinet (or loose fasteners)
No loose connections on the top plate Loose cables are wrapped and secure
All RF connections are tight Cabinet cleaned
Top surface power cable routing as Nokia drawing Fixing kit placed in packing
Document pocket variant label complies with job card Cabinet is correctly fitted to base of packing
Tie wrap bases on picture frame to drawing RF cables are not damaged (no copper exposed)
Check magnetic switch on door & sensor secure Check subrack is secure
Door/lid has earth screw & cable fitted Check subrack rails are not damaged/bent
Interior cabling is neat and not trapped Check backplane connectors are not bent
Check backplane is not scratched
Check jumper setting pins are not bent
Check cable indents
Comments
Post a Comment